how to run security camera cables through walls


how to run security camera cables through walls插图

Here are the steps you need to follow in order to run security camera cables through walls:Decide where you want to place the cameras. Make sure you can also run wires through there.Mark where you need your wires to pass through and use a drilling machine to make holes.Run the wire using fish tape.Install your camera and set it up.

How to wire a security camera?

Drilling is undoubtedly one of the best and easiest ways to run security camera wires through walls, soffit, vinyl siding, etc. If you run a Cat 5/6 Ethernet cable of your security camera, you can just drill a hole to run the Ethernet cable from the camera to your home router or NVR.

How do you mount a camera to a wall with cables?

When you’re ready to drill, using a pencil, mark a hole where the cables will go through as well as the holes for the camera’s mounting screws. Check if your camera comes with mounting stickers to help you mark the spot. Run the cables to each marked location.

How to hide a security camera?

Solution 1. When you drill a hole to run the IP camera wiring, like wiring cameras through the ceiling, you can hide the security camera cable with the wire guards. Put the cable into the guard, and attach the guard to the wall inside of your home or trail them to the back of your furniture.

What are the different types of security camera wires?

Security camera wire types usually include 3 main kinds: Cat 5/6 Ethernet cables, Siamese cables and plug-and-play cables. Cat 5/6 Ethernet cables — this type of security camera wires transmits the video/image data and power via a single cable. The Cat 5/6 cables can carry the video signal up to 1,500 feet.

How to feed fish tape to camera?

Ask your friend to help you feed the fish tape up into the hole that you just drilled for your camera, and after extending it, tape the end of the cable to the fish tape. You can pull on the tape from the outside so you can thread the cable through the hole.

Do you need a power drill for a DVR?

You will need the power drill and fish tape again. You may need to make new holes or use the same holes going to your DVR box . The idea is to make sure the cables eventually meet up to your DVR box. Go through the same process as above as necessary using the fish tape and drill.

Can you hide wires in a house?

Sometimes, no amount of cable ties and electrical tape can hide ghastly wires. There are better ways to hide cables, especially if these are security camera cables.

Where are you Planning to Install the Cameras?

The first step is to figure out where you will be placing the cameras. In this step, you need to figure out the arrangement of cameras such that they cover the whole area without leaving any blind spots. While at the same time, these spots should be placed in such a way that it is easy to wire the cameras. For example, it might seem like a good idea to place a camera in the corner, but it may be difficult to route the wires to your DVR if you do this. Instead, if you place the camera on the ceiling of your porch, you could simply run the wires through the attic.

How to run wire from soffit to DVR?

Use fishing tape to run the wire from the soffit to the DVR. If you can remove the soffit, it would make this step much easier.

How to run a cable through a wall?

You can run the cable through the walls using fish tape, although you may need the help of a friend with this step. Feed the fish tape through the camera end of the cable hole and extend it till it reaches some other hole or the DVR hole. At that end, you or your friend will tape the cable to the fish tape. Next, you just pull the fish tape back and the cable with it . Once the cable reaches your end, it will have run through the wall. If you are not able to reach the DVR hole from the camera hole directly, you will have to repeat this process for the same wire at different locations.

What happens if you place a camera higher?

The higher you place the camera, the more area it will cover and less likely it would be to get destroyed by intruders.

Can you crimp RJ45 connectors?

It would be a good idea to crimp your RJ45 connectors during this step and not before. This is because having RJ45 connectors attached to the end of your Ethernet cables may make it quite hard to fish the wire as RJ45 connectors tend to hook to places easily. You might even damage the RJ45 connectors during the process of fishing the wire and would have to crimp the connectors again. ( 1)

Can you run a security camera through walls?

Running security camera cables through walls can be tricky. But it’s easier with a few tools and the right know-how.

How to Get Audio on a Doorbell Camera?

Just as important as installation, is knowing why your equipment isn’t working, particularly doorbell cameras such as the popular Ring video doorbell. Here are a few troubleshooting steps to try if it’s not working.

What is needed for a PoE system?

You will also need a drill, drill bits, fish tape (or a coat hanger), and PoE injectors (for distance).

How to protect wires from intruders?

Also, consider securing exposed wires from intruders by using a cable run. A visible camera is a deterrent, but it can be a target for thieves. Some homeowners cover it with a wired casing or use decoy cameras, while the real device is more concealed.

What should be in a central hub?

Your central hub (which includes your NVR/router, DVR, hard drive, and screen) should be close enough to where the wiring is accessible, and not too far away from automated door locks, digital thermostats, and other electronics that are Wi-Fi enabled.

How to prevent glare in footage?

Angle it for indirect light to prevent glare in footage and images. You can also either run wires through the attic and attach the camera to the soffit or run it through an exterior wall and attach the camera using a conduit. Either way, find a sheltered area to protect the device.

What does a camera show?

A camera shows everyone that is coming and going, including lawn maintenance staff, solicitors, and trespassers. A potential intruder may use back and side doors that are away from heavy traffic areas, so cameras are a good idea here.

How to set up a camera?

How to Prepare for Setting up Wired Cameras 1 Map out the location of the best place to run wires to connect the camera to the Network Video Recorder (NVR), DVR box, and power source. (NVR or routers uses Power over Ethernet (PoE) for camera cabling.) 2 Measure cables and wires so you know how long it should be, and when drilling, leave enough space for multiple wires and cables to pass through. 3 Layout the components, and test all the equipment and cameras before installation. 4 Be sure to have a clear line of sight from each camera location, and chose a place at least 10 feet high to protect against the elements and vandalism. Don’t position cameras in such a way that it’s impossible to maintain and clean, especially if devices have backup batteries. 5 When ready to start the installation of wired cameras, turn off the building’s power supply . 6 Once you connect the input cables for multiple cameras (to the NVR/DVR box) remember to label ports and the corresponding cameras.